Ihr Warenkorb ist leer
Ihr Warenkorb ist leer Modulparameter:
Eingangsspannung: 24 V.
Ausgangsleistung 36W
Dieses Modul gibt Spannung und Strom aus:12V3A
Spulengröße: Außendurchmesser 82 mm, Innendurchmesser 30 mm.
Größe des Sendermoduls: 17 x 30 mm.
Empfängermodulgröße: 30 x 54 mm.
Die Beziehung zwischen Abstand und Ausgang ist wie folgt:
5 mm, 12 V, 3,2 A.
6 mm, 12 V, 3,2 A.
7 mm, 12 V, 3,2 A.
8 mm, 12 V, 3,2 A.
9 mm, 12 V, 3,2 A.
10 mm, 12 V, 3,2 A.
11 mm, 12 V, 3,2 A.
12 mm, 12 V, 3,1 A.
13 mm, 12 V, 3 A.
14 mm, 12 V, 2,6 A.
15 mm, 12 V, 2,5 A.
16 mm, 12 V, 2,3 A.
17 mm, 12 V, 2 A.
18 mm, 12 V, 1,8 A.
19 mm, 12 V, 1,8 A.
20 mm, 12 V, 1,6 A.
21 mm, 12 V, 1,5 A, 22 mm, 12 V, 1,5 A, 23 mm, 12 V, 1,4 A, 24 mm, 12 V, 1,2 A, 25 mm, 12 V, 1,1 A. Beachten Sie, dass der Abstand größer als 5 mm ist, da sonst die Empfangsspannung zu hoch ist und das Modul beschädigt wird
GAVRIIL MELENIOS
Bewertet in den USA am2. Januar 2025
2 out of 4 are not working. Try to contact the seller but no reply.
Ravanja
Bewertet in den USA am29. Oktober 2024
Die Medien konnten nicht geladen werden.
Eddie Offermann
Bewertet in den USA am9. Oktober 2022
I have an antique secretary desk that we use as an accent piece for the sitting room. We display some small art pieces and knick-knacks in it so I wanted to add an LED light source but didn’t want to drill holes to run power through it.These let me send power through the cabinet to operate some low power LEDs without permanently altering this beautiful antique. Would also be perfect for applications where air or water tightness are important.
Robb67
Bewertet in den USA am19. Dezember 2022
This product works exactly the way it was made. But, I had to go to YouTube, to figure out how to hook it up, and properly use it. It does a good job in what I use it for.
Customer
Bewertet in den USA am12. Oktober 2020
I purchased the 12V 2A long range version. I placed the loops 2 inches apart (I placed the top loop on top of two 2" wide masking tape rolls) as I read on some of these long range ones that you can''t get them too close. So I made sure they were separated.I connected the transmitter to my power supply, and the receiver to a digital variable load. First I thought you feed it 12V so I connected 12V up to it and got almost nothing out. Then saw the description says it will take 48V input. and went up to 30V which was the max of the power supply. I was able to get 12V at about 1.5A out of it at 2" distance. I switched power supplies to one that will go over 30V.. I slowly started ramping up the voltage and got up to about 36V and I heard a pop. The IC on the receiver blew up way before I got anywhere near 40V, never mind 48v. Waste of $40.
Produktempfehlungen
37.10€
17 .99 € 17.99€