Ihr Warenkorb ist leer
Ihr Warenkorb ist leerProduktinformation
Robuste und kompakte Bauweise:
Das Gehäuse besteht aus 1,5 mm dickem Stahl und bietet ein ausgewogenes Verhältnis zwischen Zuverlässigkeit, Größe und Erschwinglichkeit.
Anpassbare Seitenwände:
Wird mit zwei belüfteten Standard-Seitenwänden aus Stahl und einer zusätzlichen belüfteten 3-mm-Seitenwand aus transparentem Acryl geliefert, sodass Sie einen individuelleren Aufbau erstellen können.
Raffinierte Einfachheit:
Nach Jahren der Optimierung verkörpert die V3-Version des K39 die ursprüngliche Designphilosophie: Kompaktheit und einfache Installation. Die beiden mitgelieferten Griffe erleichtern das Tragen oder das Verstauen in einem Rucksack.
Bram S.
Bewertet in Deutschland am 9. Februar 2025
I ordered two of there, one of them had 2 bad welds and required drilling, the other was fine.The grill pieces (so the holes are smaller) are attached using adhesive on the sides, these come loose all the time and require different glue to keep them in place, or you can leave them out.The pci slots are not being kept into place on the bottom, so a usb expansion card or a rs232 bracket will require more drilling to fit well.I would not buy them again
Raissa
Bewertet in Deutschland am 4. März 2025
Mainboards mit fixer Slotblende passen nicht ROG X870-i - zugegeben recht massive BlendeUnterteil mit Niete fixiert, somit leider keine Möglichkeit das nicht gut klebende Mesh Gitter zu entfernen.
Dimitris Ch.
Bewertet in Deutschland am 30. Mai 2025
It said in the description that there is space for two 3.5 HDD, but there was no instructions on how to do so. I ended up mounting them behind the motherboard, from the top of the case.Also the only other "negative" thing i have to say about the position of the "cut" for the PCIE slot. I used a ASUS Prime N100I-D D4 Motherboard which has one PCIE slot in the edge and the card could be mounted on the case. If i have a second PCIE slot on my motherboard or the motherboard had its PCIE slot a bit lower you can mount the card.
Harald Koch
Bewertet in Kanada am 27. März 2025
I purchased this case to use for a Turing Pi board with RK1s installed. It's perfect; lots of airflow for cooling, and just large enough for the larger RK1 boards. Also the LEDs shining through the case make pretty patterns on the walls!
Timur Khafzetdinov
Bewertet in Deutschland am 26. Januar 2025
I was very worried that the components that I ordered might not fit, but everything worked out relatively well (there are some small flaws).Advantages :-Durable, very durable, it seems that ~2-3mm steel is very strong.-Good equipment, we didn't forget anything. Self-tapping screws, riser for GPU, belt, ties, screwdriver, just a great camping kit, And if the case does not fit , then this is a great barbecue grill.The shortcomings:-There are slight indentations and gaps of 0.1-0.2mm everywhere. But in total, it turns out that the motherboard is too tight and gets stuck in, the power supply and its cords somehow fit (forget about the management cable, there is little space, but it is possible)In the end, everything is fine!
M Drost
Bewertet in den Niederlanden am 12. Februar 2025
Bought this case for my little home server that doubles as a NAS. Installation was easier then I expected and would probably buy a K39 to minimize my workstation one day. Love it NOTE: Riser cable is NOT part of the kit. Purchase these separately. It's about 18cm long with inverse connectors on each end.
Claude B.
Bewertet in Deutschland am 5. September 2024
I would have kept it if the PSU hole could be easily used for GPU without modding as I moved to PicoPSU. Flex ATX PSU being too loud for my taste.
土鍋
Bewertet in Japan am 21. Juli 2024
非常にコンパクト。個人的にflex atx電源の入手性が悪すぎることを除けば、ほぼベストに近いケースだと思う。取説もないに等しいし、どのようにするべきか考えながら作業するのも楽しい。
Adrian Wong
Bewertet in Australien am 21. Januar 2023
I purchased the K39 v3. Did not come with a PCIe 3.0 riser cable. I used a 19cm double reverse PCIe 4.0 riser cable from ADT-link, even the case screwhole mounts for the PCIe x16 socket end of the cable lined up perfectly.Yes the case material is good and the paint work is good, however working with the case was not as simple as I thought it would be particularly the motherboard mounting frame and the ridiculous lack of clearance for the riser cable once the motherboard is installed, screwhole alignment was not a good as you'd expect at this price.I have had much build better experiences with a D19 which is a no name case at a less than half the price of the K39 and came with a riser.
David Kline
Bewertet in den USA am19. Mai 2022
Die Medien konnten nicht geladen werden.
Produktempfehlungen