Warenkorb

Ihr Warenkorb ist leer

Ihr Warenkorb ist leer

POLISI3D 2 x DC 5 V NPN NO M12 4 mm Sensor LJ12A3-4-Z/BX Induktiver Näherungssensor Schalter für 3D-Drucker CNC Z Sonde Auto Bett Nivellierung

Kostenloser Versand ab 25.99€

13.13€

6 .99 6.99€

Auf Lager

Info zu diesem Artikel

  • Es ist eine Komponente, die häufig in der automatischen Steuerungsindustrie zur Erkennung, Steuerung und berührungslosen Schaltungen verwendet wird.
  • Es kann für 3D-Drucker verwendet werden, wenn sich der Näherungsschalter in der Nähe eines Zielobjekts befindet, sendet er Kontrollsignal.
  • Da es sich um einen kapazitiven Näherungsschalter handelt, ist das Zielobjekt nicht nur auf Leiter beschränkt, sondern auch flüssige und sogar pulverförmige Dinge, wie Kunststoff, Wasser, Glas, Öl usw.
  • Weit verbreitet in der Maschine, Papierherstellung, Leichtindustrie zur Begrenzung von Stationen, Orientierungszahlen, Geschwindigkeitsversuchen usw.
  • 3-adrige Polarität: NPN-Erkennung; DC 5 V; Braun → + 5 V, Blau → GND, Schwarz → Signal (Zmin)


Eigenschaften:

Erkennungsabstand: 4 mm.

Spannung: 5 V Gleichstrom.

Ausgangsstrom: 150 mA.

Polarität: NPN

Maße: 12 x 60 mm.

Lieferumfang: 2 Stück.

JoGeDe
Bewertet in Deutschland am 7. Februar 2025
Guter Sensor, der auch mit 5V seine Aufgabe sicher erfüllt. Weitere Einzelheiten zur Fu ktion sind in der Artikelbeschreibung des Verkäufers enthalten. Immer wieder würde ich diesen Sensor erwerben.
electrospeed
Bewertet in Frankreich am 18. Mai 2024
fais le son boulot(positionneur solaire )
Miklos Bogdan Emilian
Bewertet in Großbritannien am 15. Oktober 2023
Works perfectly fine on 5v. Super accurate with a 4mm detection.
wolfman
Bewertet in Großbritannien am 12. November 2022
These work reliably as endstops. They are not recommended as Z probes though as you really need a point detector not a general closeness detector for accurate z probing.The only downside I see is that the detection range for aluminium is probably more like 2mm not 4mm, however if you can use steel to detect it is a good 4mm.I have 5 of these used as endstops on various CNC machines and they all work reliably.`
Alain Gauché
Bewertet in Frankreich am 20. Juni 2021
Utilisé pour remplacer le capteur sur dagoma discoeasy 200. Fonctionne parfaitement.
Wallace E Owen
Bewertet in den USA am18. August 2020
I print higher temp materials on moderately modified commercial printers in heated enclosures.I found the BLTouch and clones don't tolerate heat well, becoming a bit erratic after several excursions to 75c.Switching to this inductive probe means I have lost the ability to use a glass sheet, but the popular steel sheets with PEI coating work fantastic. I even found that the probe works through a thin sheet of garolite cemented to the steel side, so printing nylon is now much easier.I do wish the cable was about 30cm longer, so it could reach all the way to the Z end-stop connector without the need to splice the extra needed length.
Produktempfehlungen

13.55€

6 .99 6.99€

4.9
Option wählen

11.99€

4 .99 4.99€

4.8
Option wählen

16.90€

7 .99 7.99€

5.0
Option wählen