Ihr Warenkorb ist leer
Ihr Warenkorb ist leer Panasonic Original ADA29A115 Aufnahmeschaft für:
Panasonic SD-200, SD-206, SD-207, SD-250, SD-251, SD-252, SD-252WXC, SD-253, SD-254, SD-254WTS, SD-254WXC, SD-255, SD-255WTS, SD-255WXS. A, SD-25 5WXC, SD-255WXE, SD-256, SD-256WTS, SD-256WXC, SD-256WXE, SD-257, SD-257WST, SD-257WTS, SD-257WXA, SD-257WXC, SD-257WXE
Montageanleitung: Schauen Sie sich vor dem Entfernen die ursprüngliche Schaftposition an, um sicherzustellen, dass Sie die neue Befestigungswelle in der gleichen Ausrichtung anbringen.
Die Knetklinge mag locker am Schaft erscheinen, aber so ist es so konstruiert, dass es passt. Tauschen Sie die Welle aus diesem Grund nicht aus. Der Hauptgrund, warum Sie die Befestigungswelle ersetzen möchten, ist, wenn die Dichtung versagt und Mischung in die Pfanne sickern lässt, oder wenn das Lager ausfällt und es entweder festsitzt oder übermäßige Geräusche während des Betriebs macht.
Louisa
Bewertet in Großbritannien am 28. Juni 2024
Part as described exactly perfect fit for my Panasonic bread maker. Comes with screws
Robert
Überprüft in Belgien am 2. Juni 2024
Het onderdeel was bestemd voor een broodbakmachine. Het type nummer was overplakt door een ander nummer en paste niet. De doorsnede moest 61mm zijn maar was 69mm. Volgens mij is de missing gebeurd bij de verzender. Het tweede onderdeel was wel in orde
Widget
Bewertet in Deutschland am 18. Juni 2024
I've had my Panasonic SD-253 for over 15 years now. It is used a couple of times every week on average, but the bucket was starting to leak a little and the mixing paddle was becoming loose, but otherwise it works fine.This is far cheaper than a complete bucket and only take 5 minutes to fit.Perfect for me.
Charles
Bewertet in Großbritannien am 10. Dezember 2024
This has brought new life to my old breadmaker pan whose bearing was getting very stiff. It seems well made and is easy to fit. It comes complete with a new silicone seal and three screws. Note that there's only one correct orientation. As other reviewers have said, make sure to use a Philips screwdriver, not a Pozidriv.
Jason Simpson
Bewertet in Großbritannien am 5. Mai 2023
after 13 years.Fitted perfectly. New seal and screws provided.Easy to install. Just give the bread container a good clean.If the container’s non-stick has worn you can get the whole thing replaced.At the time I bought:£23 for mount or £55 for whole container (which includes a mount).
AJC
Bewertet in Großbritannien am 12. August 2021
We have had our SD251 for a considerable time. Used 2 to3 times a week it has been perfect. However the shaft at the bottom of the bread pan was getting stiffer and stiffer to turn. (it was not leaking) I thought about stripping the unit down to see if I could free up and lubricate the bearing; but when I saw that the mounting shaft assembly was available for just £20ish and as the pan is still in reasonable order that I would go for it. I am glad I did. This replacement came in a plain box with a new seal, three replacement screws and appears absolutely identical to the original.To fit is relatively easy starting with the pan upside down:-1. Strip by original off the pan by undoing the three PHILLIPS retaining screws. ( make sure you have exactly the correct screwdriver bit to fit the screws.) ours came out with remarkably little effort but make sure you have the pan firmly held and use downward force to keep the screwdriver well engaged as you turn anticlockwise.2. You may need to give the old shaft a tap to free it off but the old unit should now come away.3. Inspect the exposed base of the pan and clear away any debris, clean up the recess for the seal.4. Place the new seal in the recess, it does not seem to have a specific way up.5. Carefully position the new shaft unit into place making sure the screw holes are lining up.6. Now LOOSELY put all three new screws in. Do not tighten but just gently nip them up. Turn the unit over and check on the inside of the pan that the seal is in place. You can just see the edge of it in the well. If any of the seal is protruding into the pan then it is not properly seated and you must start again.7. Turn the pan back upside down, to make sure the assembly seats correctly go round the screws tightening up each a little at a time until all three are tight. Taking care not to overtighten.8. The job is now complete, to be sure I had a good seal I filled the pan with water and let it stand for a while. I had no leaks. The pan has now been used a few times and is working perfectly.In my case I notice that the kneading arm is a bit loose on the shaft, this I think is due to wear on the arm, however it seems alright at the moment, I will replace it if it gets any worse.I hope this review is helpful, I am well pleased with the result of fitting this new shaft assembly to our breadmaker.AJC
Produktempfehlungen
