Ihr Warenkorb ist leer
Ihr Warenkorb ist leer
Indikationen:
Code: 4M-10
Material: 20CrMo legierter Stahl
Gewicht: 7g/set (0.25oz)
Übersetzungsverhältnis: 24/12,2: 1 (gleich Lagerbestand)
Michael R
Bewertet in den USA am19. Januar 2025
I installed these in a JJRC c8808 and I’m very happy with them
JB
Bewertet in Kanada am 21. Januar 2024
These full metal gears are a great upgrade for the trx4m. Very easy to install and while you have it apart I recommend the bearing kit as well. My stock plastic gears stripped out so I got these and they are a great price and fit perfectly
gt60
Bewertet in Deutschland am 16. Oktober 2024
Eins der 24er Zahnräder läuft nicht wegen unrundem Lauf, somit zu teuer. Nach der schlechten Bewertung hat sich der Händler gemeldet und das Problem behoben indem ich für das fehlerhafte Teil Ersatz kostenlos bekommen habe . Toller Service 👍 Danke
James
Bewertet in den USA am24. April 2024
After a brief stint with analysis paralysis over stock vs. OD/UD diff ratios, I decided to go with these for both stock plastic front and rear axle housings and change gear ratios later when I upgrade to the Diamond axles. The two shim washers provided give you ample adjustment range, and after mixing and matching I found the perfect combo (both washers in front diff and only one in the rear). If you’re reading these reviews and you’re worried about potential binding, as I was a week ago, be sure to grease up the gears a little before making adjustments. It’s a little messier, but it gave me the honest feedback I needed to ensure everything was shimmed properly and I wasn’t just fighting dry helical gears. Also, I highly recommend getting the bearing upgrade kit and ditching the bushings, as this makes the whole machine buttery smooth now. I have zero binding through full steering articulation and the power delivery is unmuted.
Rainer Lichtenegger
Bewertet in Deutschland am 5. September 2023
Passgenau u. Leichte Montage
Peter Porn
Bewertet in Deutschland am 4. Juni 2023
Paßt alles gut
Kunde
Bewertet in Deutschland am 25. Februar 2023
Sehr zufrieden!!!
Trudi
Bewertet in Deutschland am 22. September 2023
Passgenauigkeit und Funktion einwandfrei.Klare Kaufempfehlung.
Chocolate Marbel
Bewertet in den USA am20. Januar 2023
Please read my entire review:Quality of these things is crazy for the price. The gears seem to be hardened as well from what I can tell, gear mesh is pretty decent and no binding! Love that these are helical gears similar to real trucks.**As the title states, theses are not compatible with the stock bushings. The differential shoulders are knurled to grip onto the inner race of the bearing kits. Obviously if you decide to run the bushing and go against my advice you will end up with either severe binding or badly worn differential carrier bushings. Buy any bearing kit with this purchase.Some modification is required**So now the pinion bearing fit is extremely tight and you will not be able to slide the pinion down onto the bearings as intended. To remedy this I chucked the tip of the pinion gears. Onto my drill gently and with a tiny sliver of 800 grit sand paper, spun/sanded the shaft/ bearing fit down so to resolve this issue. At medium speed with 800 grit this took less than 1 minute of sanding/spinning and voila. Done. I had fast eddy bearings, results may vary.
Wallace Routh
Bewertet in den USA am2. Oktober 2023
I’ve read some reviews where people had issues fitting the bearings on the ring and pinion but mine went on absolutely perfect! Great quality as usual, I’m very happy with them, a great upgrade!
ZiPZaP_33
Bewertet in Deutschland am 17. November 2023
Funktioniert super ohne Probleme plug and Play
Produktempfehlungen
