Ihr Warenkorb ist leer
Ihr Warenkorb ist leerProduktbeschreibung des Herstellers
Koos glasbergen
Bewertet in den Niederlanden am 9. Juni 2025
Leuk om te maken
Jay Stevens
Bewertet in den USA am28. Oktober 2024
This product is able to build either a single track bridge or a double track bridge. Parts for both are included, although if you're making a double track bridge you will also need to order Faller 222540 (which is a set of extra bridge decks).The instructions in the kit aren't the best, but thankfully it is very straightforward. Things slot together quite well, although sometimes they can be a little fiddly to get square.Note that in the pictures I have not glued down the bridge decks yet. They have a little join right underneath the railings where they slot into the bridge frame. I'm leaving them loose until I put track in, hence why in some of the pictures they seem to be floating a little.I did have to remove some flashing from the kit using a hobby knife. Otherwise, the molded plastic is alright; it's not fantastic but it's also not awful. It's about average for an injection molded kit.The bridge itself is 40 cm long. It's made up of a primary arch (20cm long) and 2 half-arches (10cm long each). You can opt to just build the primary arch if needed, since each of the bridge decks are the same length as the arches. They join together quite well. Although the bridge deck slots together without glue, you will need to glue the bridge frame together.Clearance under the bridge without the added pillars is about 57mm. Without pillars it is about 70mm to the track, and 76mm to the top of the bridge railing.The bridge is about 64mm wide (almost exactly 2.5 inches). It's about 35mm from the centerline of one track to the centerline of the next track.2 sets of pillars are provided. The smaller set of pillars is about 6mm high; the taller pillars are about 10mm high. In the double-track setup, you need to cut off the end of 2 sets of pillars and join them together; there's a place to cut the plastic to allow you to do this. However, this cut wasn't clean for me, so I had to do some sanding to clean it up well enough to join them together. Even then, there is a visible crease where the pillars meet.With the smaller set of pillars, you can raise the track to be about 76mm from the ground, or almost exactly 3 inches. This is a little taller than I expected, and I wasn't able to find that info online.Overall, this is a fine bridge kit that works exactly as expected.
RENATO
Bewertet in Italien am 5. Juni 2021
Faller 'sempre una garanzia per chi vuole costruire un plastico ferroviario
KST
Bewertet in Deutschland am 25. Februar 2020
Sieht gut aus und fügt sich gut in die Umgebung ein
Cliente
Bewertet in Spanien am 14. November 2020
Todo bien
Stephanie
Bewertet in Deutschland am 11. Februar 2020
Das Produkt hat mich total enttäuscht. Brücke ist instabil und sieht im Original ziemlich billig aus. Besonders den relativ hohen Preis kann ich mir nach dem Erhalt nicht mehr erklären.
Kunde
Bewertet in Deutschland am 23. Januar 2019
schnell aufzubauen, auch für 12-jährige
julien B
Bewertet in Frankreich am 14. Februar 2019
Solide mais difficile à coller car petits morceaux, colle glue obligatoire.
Jonny
Bewertet in Deutschland am 10. Juli 2019
schöne Brücke, habe ich zusammengebaut und bemalt, wird in meine Anlage eingebaut, super Artikel, kann ich weiterempfehlen.
roli457
Bewertet in Deutschland am 10. Mai 2019
Einfaches zusammenbauen, sehr detailliert, ansprechendes Modell, gutes Preis - Leistung Verhältnis
Sagt-Dir-Was
Bewertet in Deutschland am 21. November 2018
Unter den Produktdetails steht unter "Spurweite" "Nein". Die ist definitiv falsch. Auf der Verpackung steht Spurweite "N" und ist somit nicht für die Spurweite "H0" geeignet.Ich werde die Brücke leider zurückschicken müssen.
Produktempfehlungen